Welcome to Answerclub.org
Questions | Answers | Discussions | Knowledge sharing | Communities & more.
Sign Up to our social questions and Answers Engine to ask questions, answer people’s questions, and connect with other people.
Login to our social questions & Answers Engine to ask questions answer people’s questions & connect with other people.
Lost your password? Please enter your email address. You will receive a link and will create a new password via email.
Please briefly explain why you feel this question should be reported.
Please briefly explain why you feel this answer should be reported.
Please briefly explain why you feel this user should be reported.
Questions | Answers | Discussions | Knowledge sharing | Communities & more.
Type one PC cards:
Type I cards can be up to 3.3mm thick, and are used primarily for adding additional ROM or RAM to a computer. Type II cards (the most common) can be up to 5.5mm thick. These cards are often used for modem, fax, SCSI, and LAN cards. Type III cards can be up to 10.5mm thick, sufficiently large for porRead more
Type I cards can be up to 3.3mm thick, and are used primarily for adding additional ROM or RAM to a computer. Type II cards (the most common) can be up to 5.5mm thick. These cards are often used for modem, fax, SCSI, and LAN cards. Type III cards can be up to 10.5mm thick, sufficiently large for portable disk drives.
See lessrepresents a jumper being open. On a three-bit jumper block on a SCSI drive,
represents a jumper being open. On a three-bit jumper block on a SCSI drive, 11
represents a jumper being open. On a three-bit jumper block on a SCSI drive, 11
See lessYou are testing the resistance in Ohms of a fuse on a 15K amp system. If the fuse is good, the meter should read?
You are testing the resistance in Ohms of a fuse on a 15K amp system. If the fuse is good, the meter should read 0
You are testing the resistance in Ohms of a fuse on a 15K amp system. If the fuse is good, the meter should read 0
See lessIn the Binary numbering system, a (1) represents a jumper being shorted and a (0) represents a jumper being open. On a three-bit jumper block on a SCSI drive, how would an ID of logical 3 be set?
represents a jumper being open. On a three-bit jumper block on a SCSI drive, an ID of logical 3 be set 11
represents a jumper being open. On a three-bit jumper block on a SCSI drive, an ID of logical 3 be set 11
See lessA system has two IDE hard drives that are each divided into primary and extended partitions, which drive letter is assigned to the primary partition of the second drive?
A single IDE interface and ribbon can support two devices. In this configuration, one device is designated as primary, or leading, and the other device is designated as secondary, or alternative. In this way, two drives can share the same cable without conflict.
A single IDE interface and ribbon can support two devices. In this configuration, one device is designated as primary, or leading, and the other device is designated as secondary, or alternative. In this way, two drives can share the same cable without conflict.
See lessA system has two IDE hard drives that are each divided into primary and extended partitions, which drive letter is assigned to the primary partition of the second drive?
A single IDE interface and ribbon can support two devices. In this configuration, one device is designated as primary, or leading, and the other device is designated as secondary, or alternative. In this way, two drives can share the same cable without conflict.
A single IDE interface and ribbon can support two devices. In this configuration, one device is designated as primary, or leading, and the other device is designated as secondary, or alternative. In this way, two drives can share the same cable without conflict.
See lessAfter installing a sound card, the system locks up when a parallel port tape backup unit is also used. What is most likely the problem?
An IRQ (Interrupt Request) is a signal sent by a device to the CPU
An IRQ (Interrupt Request) is a signal sent by a device to the CPU
See lessWhat would you ask to determine if the display is working?
The most common issues of Android screens are dead and stuck pixels. Dead pixels occurs when small color pigments of your screen gets busted, resulting to a black spot on your screen, while stuck pixels are color pigments of the display that are frozen, unable to change to other colors like it normaRead more
The most common issues of Android screens are dead and stuck pixels. Dead pixels occurs when small color pigments of your screen gets busted, resulting to a black spot on your screen, while stuck pixels are color pigments of the display that are frozen, unable to change to other colors like it normally should. These issues can easily be avoided if you can detect it while the problem is still not that severe. That’s why testing your LCD display is outright important and needs to be done frequently to avoid any issues from worsening.
See lessYour CD-ROM audio cable connects to the:
sound card A cable used to send audio CD sound to the computer's sound card. When playing audio CDs, CD-ROM drives output analog sound to both a headphone jack and external connector just like a CD player.
sound card
See lessA cable used to send audio CD sound to the computer’s sound card. When playing audio CDs, CD-ROM drives output analog sound to both a headphone jack and external connector just like a CD player.
A capacitor is measured in which of the following units?
The capacitance value of a capacitor is measured in farads (F), units named for English physicist Michael Faraday (1791–1867).
The capacitance value of a capacitor is measured in farads (F), units named for English physicist Michael Faraday (1791–1867).
See less