Home/ Rajeswari/Answers
Ask Rajeswari
  1. Asked: June 11, 2024In:

    A PCMCIA measuring 10.5mm is what type?

    Rajeswari
    Rajeswari Knowledge Contributor

    A PCMCIA measuring 10.5mm is what type 3

    A PCMCIA measuring 10.5mm is what type 3

    See less
  2. Asked: June 11, 2024In:

    Whenever you have a hardware resource conflict, it will more likely be an IRQ conflict rather than an i/o conflict because:

    Rajeswari
    Rajeswari Knowledge Contributor

    Settings are parameters that control the behavior and performance of the hardware, such as the IRQ, DMA, I/O address, or memory address. Conflicting settings can cause hardware conflicts, as they may assign the same resources or channels to different devices, resulting in collisions or interference.

    Settings are parameters that control the behavior and performance of the hardware, such as the IRQ, DMA, I/O address, or memory address. Conflicting settings can cause hardware conflicts, as they may assign the same resources or channels to different devices, resulting in collisions or interference.

    See less
  3. Asked: June 10, 2024In:

    Which I/O port belongs to LPT2?

    Rajeswari
    Rajeswari Knowledge Contributor

    An I/O address, also called a "port address," references a separate memory space on PC peripheral boards, similar to memory-mapped peripherals that use blocks of memory. Peripherals often use both methods: an I/O address for passing control signals and memory for transferring data.

    An I/O address, also called a “port address,” references a separate memory space on PC peripheral boards, similar to memory-mapped peripherals that use blocks of memory. Peripherals often use both methods: an I/O address for passing control signals and memory for transferring data.

    See less
  4. Asked: June 10, 2024In:

    Which of the following FRUs would be considered both an input/output device?

    Rajeswari
    Rajeswari Knowledge Contributor

    Modem: A modem is considered an input/output device because a modem sends and receives data at the same time.

    Modem: A modem is considered an input/output device because a modem sends and receives data at the same time.

    See less
  5. Asked: June 10, 2024In:

    The ESD wrist strap is designed to protect PC Components or Service Technicians ?

    Rajeswari
    Rajeswari Knowledge Contributor

    The Wrist Strap is the first line of ESD control. Using the Wrist Strap to electrically connect the computer chassis and the operator will keep them at the same electrostatic potential so no ESD event or discharge can occur between the chassis and the operator.

    The Wrist Strap is the first line of ESD control. Using the Wrist Strap to electrically connect the computer chassis and the operator will keep them at the same electrostatic potential so no ESD event or discharge can occur between the chassis and the operator.

    See less
  6. Asked: June 10, 2024In:

    The ESD wrist strap is designed to protect PC Components or Service Technicians ?

    Rajeswari
    Rajeswari Knowledge Contributor

    The Wrist Strap is the first line of ESD control. Using the Wrist Strap to electrically connect the computer chassis and the operator will keep them at the same electrostatic potential so no ESD event or discharge can occur between the chassis and the operator.

    The Wrist Strap is the first line of ESD control. Using the Wrist Strap to electrically connect the computer chassis and the operator will keep them at the same electrostatic potential so no ESD event or discharge can occur between the chassis and the operator.

    See less
  7. Asked: June 10, 2024In:

    What problem can occur if a printer cable is to close to a power cable?

    Rajeswari
    Rajeswari Knowledge Contributor

    Check the USB cable for damage and recommended length, and then restart your printer and computer. Turn off the printer and the computer. Disconnect the USB cable from the computer and printer, and then inspect the cable. If the cable is damaged or longer than 3 m (9 ft 10 in), replace it.

    Check the USB cable for damage and recommended length, and then restart your printer and computer. Turn off the printer and the computer. Disconnect the USB cable from the computer and printer, and then inspect the cable. If the cable is damaged or longer than 3 m (9 ft 10 in), replace it.

    See less
  8. Asked: June 10, 2024In:

    How can you totally protect a PC from damage during an electrical storm?

    Rajeswari
    Rajeswari Knowledge Contributor

    5 Tips to Protect Your Electronics in Lightning Storms Unplug Your Devices. ... Use a Lightning Protection System. ... Don't Rely on Surge Protectors. ... Look Into Getting a Whole-House Surge Protector. ... Review Your Insurance Coverage. ... Contact Prism Specialties.

    5 Tips to Protect Your Electronics in Lightning Storms
    Unplug Your Devices. …
    Use a Lightning Protection System. …
    Don’t Rely on Surge Protectors. …
    Look Into Getting a Whole-House Surge Protector. …
    Review Your Insurance Coverage. …
    Contact Prism Specialties.

    See less
  9. Asked: June 10, 2024In:

    How can you totally protect a PC from damage during an electrical storm?

    Rajeswari
    Rajeswari Knowledge Contributor

    5 Tips to Protect Your Electronics in Lightning Storms Unplug Your Devices. ... Use a Lightning Protection System. ... Don't Rely on Surge Protectors. ... Look Into Getting a Whole-House Surge Protector. ... Review Your Insurance Coverage. ... Contact Prism Specialties.

    5 Tips to Protect Your Electronics in Lightning Storms
    Unplug Your Devices. …
    Use a Lightning Protection System. …
    Don’t Rely on Surge Protectors. …
    Look Into Getting a Whole-House Surge Protector. …
    Review Your Insurance Coverage. …
    Contact Prism Specialties.

    See less
  10. Asked: June 10, 2024In:

    What problem can occur if a printer cable is to close to a power cable?

    Rajeswari
    Rajeswari Knowledge Contributor

    Check the USB cable for damage and recommended length, and then restart your printer and computer. Turn off the printer and the computer. Disconnect the USB cable from the computer and printer, and then inspect the cable. If the cable is damaged or longer than 3 m (9 ft 10 in), replace it.

    Check the USB cable for damage and recommended length, and then restart your printer and computer. Turn off the printer and the computer. Disconnect the USB cable from the computer and printer, and then inspect the cable. If the cable is damaged or longer than 3 m (9 ft 10 in), replace it.

    See less